| |||||||
Dell Mini 9 Guides Guides, Articles and How-To's for the Dell Mini 9
![]() |
| | LinkBack | Article Tools | Display Modes |
| ||||||||||
| |||||||
Dell Mini 9 Guides Guides, Articles and How-To's for the Dell Mini 9
![]() |
| | LinkBack | Article Tools | Display Modes |
| by acabtp 09-29-2008, 08:37 PM
Maxing out the memory (RAM) on your Dell Mini is easy, cheap, and effective. Do it today! Frequently Asked Questions I thought the max was 1 gb? Why doesn't Dell offer it with more? - In order to ship the Mini with Windows XP instead of Windows Vista, there are some hardware specs that the Mini needs to be below, one of which is a maximum installed memory of 1 gb. This is just a restriction at the time of sale... the Mini hardware and the version of XP Home preinstalled on the Mini both work just fine with more than 1 gb RAM. Will this void my warranty? - No, as long as you are careful and do not break anything. What kind of memory can I use? - Any DDR2 SODIMM (laptop memory chip) that runs at 533 MHz (DDR2-4200) or faster. 2 gb chips are big and cheap, so it is the only size that makes sense to buy for now. Where did you get your memory? How much did it cost? - You can get it anywhere, DDR2 SODIMM chips are standardized, and it is not specific to the Mini. Expect to pay between $30 (online) and $50 (brick and mortar). Buy the memory from Crucial for just $28 USD Can I use a RAM chip with tighter timings? - Yes, you can. As long as the memory you are using has its performance timing value stored in the SPD, the Mini will use them. You cannot however specify the memory timings manually in the BIOS; they must be stored in the chip's SPD. Does the Mini support RAM speeds greater than 533 MHz? - No. On to the installation... Swapping out the RAM Start by turning the Mini over and removing the two screws indicated by the red circles. Use your finger to gently pry the module cover up at this area and pop it out and remove it Gently pull the two metal tabs indicated by the circles to the sides, away from the center of the memory chip. The chip will pop up to about a 25° angle and you can remove it. Insert the new chip into the socket, making sure it is fully seated. Note that you cannot see the gold contacts at the bottom of the chip when it is fully inserted in the socket. Gently press down on the chip until the two metal tabs you moved before lock into place on the new chip. This does not take much effort at all (one finger) so if there is any resistance, make sure you have the chip seated properly. Replace the module cover, starting with the edge closest to the front of the laptop. Gently bend it like so to help the side clips snap back into place. Once the cover is snapped back on, just replace the two screws you removed at the start and power the unit back up! No configuration steps are necessary, and you should see your newly installed memory available in your OS. |
| Views 208474
Comments 185
|
(#21)
|
| Junior Member Posts: 8 Join Date: Oct 2008 | Quote:
You would have to have a 64bit version of windows loaded. Or perhaps a linux distro of course. | |
| |
(#22)
|
| Junior Member Posts: 2 Join Date: Oct 2008 | Cheers on the write up. Same for me and the initial replier, I've done alot with computers so this is basic. But appreciate you taking the effort man! Great starting point for novices! |
| |
(#23)
|
| Junior Member Posts: 3 Join Date: Oct 2008 | So did anyone go with 4-4-4-12 ram? Can you confirm the timings? Faster is always better! Can you even adjust the timings in the bios? Thanks helm |
| |
(#24)
|
| Senior Member Posts: 187 Join Date: Oct 2008 Location: Orlando, Florida | Quote:
I have confirmed the timings using CPUZ. You cannot adjust any timings in the BIOS. Black / BIOS A05 / Dual Booting XP Pro and Ubuntu 9.04 / 2GB RAM / 16GB SSD / BT 2.0 / 1.3MP Webcam / US-INTL Keyboard U061H Extras: 16GB SDHC Sleeve External Drive Skin Buffalo MicroSD USB Memory Stick w/8GB MicroSD | |
| |
(#25)
|
| Junior Member Posts: 3 Join Date: Oct 2008 | Thanks! |
| |
(#26)
|
| Junior Member Posts: 14 Join Date: Sep 2008 Location: Virginia | well i decided to give this mod a shot since it was so easy and relatively inexpensive. the ram was easy to swap out, even a novice would be able to do it as long as they had a small philips screwdriver for the back panel. the mini booted up with no problems and recognized the ram immediately (corsair value select). not sure if i'm noticing any performance improvements but i don't use my mini for anything other than surfing the web - 1 window of firefox open with about 6-7 tabs. maybe its faster or maybe its just in my head! ![]() |
| |
(#27)
|
| Member Posts: 72 Join Date: Oct 2008 | I found this while looking at the Kingston. It's at least a lot better price. http://www.newegg.com/Product/Product.a ... 6820231202 XPS M1330, T9300, 4gb DDR, 128gb SSD, 128mb Nvidia, LCD Screen, BT, Wireless-N, Soundblaster (320gb HDD w/ Windows 7) |
| |
(#28)
|
| Senior Member Posts: 176 Join Date: Sep 2008 Location: Texas | Quote:
wow! killer deal there! I ordered two, one for mine and one for the wife's.... | |
| |
(#29)
|
| Senior Member Posts: 163 Join Date: Sep 2008 Location: San Diego / Ca / USA | Quote:
Dell Mini 9 8 gig ssd 1 gig ram .3mp cam powerbook G4 ( needs to be refreshed still on 10.4) | ||
| |
(#30)
|
| Junior Member Posts: 25 Join Date: Oct 2008 | I am a bit confused about the speeds on RAM. I understand that the mini will run all ram at 533, but I do not understand the difference between say PC5400 and PC6400. What would be the advantage of 5400 vs 6400 or is this just a different type of ram? I am assuming I could pickup some PC5400 that runs at 667mhz and it would just be run at 533? |
| |
![]() |
| Article Tools | |
| Display Modes | |
| |
Copyright © 2008-2010 MyDellMini.com.
Hosted on a CatN PHP vCluster.